The kit and its assembly:
This relatively simple build was triggered by the “In the navy” group build at whatifmodelers.com in April/May 2020, even though I started it too late for the deadline.
After having recently read a lot of stuff about the Falklands/Malvinas conflict, I wondered if Argentina could not have procured a dedicated fighter for its single carrier – and the F-8 from US surplus stocks was a perfect candidate for the potential timeframe of the Seventies, when the type was retired from USN/USMC service or, in part, modernized and/or put up for sale, like the machines for the Philippines. The only real-world problem would have been the weight: the F-8E weighed up to 15 tons, while the Super Étendard, which was reportedly already hard to launch from Veinticinco de Mayo, had a MTOW of “only” 12 tons. Not certain if the F-8’s afterburner engine and the wings’ raised angle of incidence would have been enough to launch a Crusader? Well, it’s whifworld, after all. 😉
The basis is the Hasegawa F-8E, a kit that I had originally stashed away as a donor for a different project.
The model was built mostly OOB, I just sanded the dorsal avionics hump away and gave the machine a pair of drop tanks under the wings (from an A-4) – a rather unusual sight on a Crusader, and it looks even more weird with the wings in the raised position! The Sidewinders, relatively simple pieces, too, were taken OOB, since they look very much like early AIM-9Bs.
The kit goes together well, but it is a simple affair and you see the mold’s age. You get raised (though fine) panel lines, a rather simple cockpit tub with flat dashboards (for decals), a clumsy seat and no cockpit back wall at all. Fit is basically O.K., but the windscreen refused to fit well, and the hatch turned out to be somewhat too narrow for the rear bulkhead you are supposed to glue into it. Furthermore, the fuselage halves, especially on the underside, have shallow shrink areas close to the seams, so that PSR is mandatory. I would, not call the kit my first choice for the F-8 (which would rather be the Academy kit), but you get the Hasegawa kit at reasonable prices, and I originally purchased it as a body donor bank.
Since the kit lacks a proper air intake duct, sanding the fuselage halves inside of the respective orifice is not easy - I used a soft acrylic putty and left the radome away until the job was done. Furthermore, I added a visual blocker inside of the intake, a piece of black foamed styrene under the cockpit tub - otherwise you have direct sight down the empty interior in a head-on view.
Further small additions are some blade antennae on the hull and on the fin, inspired by the Argentinian Skyhawks.
Painting and markings:
Again, I wanted a rather subtle, semi-authentic look. The most natural choice would certainly have been a Light Gull Grey/White livery like the A-4Qs, but for a twist and because I like the late French F-8Ps in their all-over dark grey livery, I settled upon something that resembles the French/Argentinian Super Étendards: a dark, bluish-grey upper surface with white undersides and the upper colors well wrapped around the wings’ leading edges.
Concerning the French grey tone there are many different opinions and recommendations – ranging from Dark Gull Grey (FS 36231, which is IMHO much too light) over Gunship Grey (FS 36118) to dark blue.
I settled for Humbrol 79 (Blue Grey) as basic tone, which is AFAIK Humbrol’s interpretation of the German RAL 7012 (Basaltgrau), a tone that is very close to the British Dark Sea Grey. The undersides, including the landing gear, were painted with acrylic semi-gloss white from a rattle can. This was done as the first step, with a masked low waterline. Then the grey was applied by brush, and also wrapped around the wings’ leading edges. In order to improve the camouflage effect from above, the pylons as well as the outer sides of the stabilizers under the tail were painted in blue grey, too.
The flags on the rudder as well as the on the stabilizers were painted with white and Humbrol 48 (Mediterranean Blue), too, just the sun emblems on the fin are decals. Since the F-8 has, unlike the A-4 or the Sue, all-mowing stabilizers, I decided to paint the whole tail surface in white and blue and not just the trailing edge. This looks quite bright, but it is IMHO a great detail that sets this whif really apart and shows some pride.
The afterburner fairing was painted with a mix of Humbrol 27002 and 27003 (Polished Aluminum and Steel Metallizer) and later treated with graphite for a burnt look.
After an overall black ink wash the upper surfaces were treated with dry-brushed post shading (Humbrol 106 and 156). The decals come primarily from an Academy Super Étendard, augmented by markings from various decals from an Airfix Falklands War kit set sheet (e.g. the sun icons for the fin flash).
The silver leading edges of the wings, stabilizers and the fin were created with decal sheet material. the same material in black was used for walkway markings.
Decals come primarily from an Acedemy Super Étendard sheet, the tactical code was modified. Only the sun icons on the fin flash had to be procured from a different source (an Airfix A-4 Skyhawk sheet). The stencils come from the Hasegawa OOB sheet.
Finally, the kit received an all-over coat of matt acrlyic varnish.
